Evolution Lithium

Are Solar Lithium Batteries Good as a Second Battery for Car Audio?

Yes, some solar and camping lithium batteries can work as a second battery for car audio. The catch is how much current they can deliver and whether your car can charge them correctly. A big Ah number on the case does not mean they can feed a big amp.

You spot a cheap 100Ah or 200Ah lithium battery online and think: “Would that be good as a secondary for my sounds?” Before you buy it, find the exact model and check its continuous discharge rating. That tells you far more about its suitability for bass than the size of the case.

As a rough guide, 100A from the battery supports about 1,000W RMS from a Class D amp at 12.8V and 80% efficiency. At 200A, that becomes about 2,000W. Those are calculated estimates before wiring losses and extra breathing room. Your alternator can contribute too.

That may suit a smaller daily setup under ,1-2k rms. Long demos on a big monoblock are a different job.

What Makes a Battery Suitable as a Secondary?

A battery in the boot gives your amps a nearby supply of stored energy. It can help feed heavy bass passages and give you more playing time with the engine off. But it still needs to deliver enough current without the voltage dropping too far.

Three questions matter when assessing a battery listing:

  • Can it keep up when the bass stays loud? Check continuous discharge amps.
  • Can your car charge it properly? Check charging voltage and current limits.
  • Will it give you enough playing time? Check usable capacity for your listening habits.

A battery that runs a camping fridge all weekend may still struggle to feed a big monoblock. Playing time and the ability to deliver a lot of current are different things.

If you are still deciding whether extra reserve is necessary, start with our guide to whether you need two batteries for car audio. Here, we are checking whether the battery you have found is up to the job.

Why a 100Ah Battery Does Not Automatically Deliver Huge Current

Amp-hours and amps describe different things.

Ah helps describe how much charge a battery holds. Amps tell you how quickly it can supply that charge to your system. At the same voltage, more usable Ah generally means more playing time at the same load. It does not automatically mean more current.

A 100Ah battery might be rated to deliver 100A continuously, or something quite different. The cells, connections, protection electronics and terminals all need to handle the load.

For example, imagine two 100Ah batteries: one rated for 100A continuous and another rated for 300A. They have the same Ah label, but the second can deliver three times the current. This is an example to explain the difference, not a rating for any particular product.

For bassheads shopping second-hand or comparing online listings, ask for the manufacturer’s specification sheet. “Lithium”, “deep cycle” and “solar compatible” are not discharge ratings.

How a 100–200A BMS Can Limit a Storage Battery

Many prebuilt 12V LiFePO₄ batteries sold for camping, solar and storage use contain an internal battery management system, commonly called a BMS. Models with 100A or 200A continuous discharge ratings are readily available. That range is not a universal limit for LiFePO₄ batteries.

For example:

Those are the manufacturers’ published ratings; we have not bench-tested those two batteries. Check the exact version you are buying.

The Protection System May Disconnect the Battery

A 100A rating does not mean the battery gently holds the current at 100A. It may supply more for a short time, then cut off when its protection trips. It can also disconnect if it gets too hot or a cell reaches a voltage limit.

Depending on what else is supplying power, that can mean a sudden voltage drop, the amp going into protect, or the sounds cutting out.

A big peak-current figure on the listing is worth checking closely. How long is that peak allowed to last, and what happens afterwards? A brief surge rating will not tell you whether the battery can handle a long bass note.

Do not bypass the protection to get more current. Choose a battery built for the load. An active balancer helps keep cell-group voltages even; it does not increase current capability or replace overcurrent protection.

The Practical Rule: About 1,000W RMS per 100A

For a quick check on a conventional 12V setup, allow roughly 100A for every 1,000W RMS from a Class D amp. Use it to spot an obvious mismatch, then check the actual system and leave some breathing room.

The calculation is:

Estimated amplifier output = supply voltage × input current × amplifier efficiency.

At an assumed 12.8V supply and 80% efficiency:

Current available to the amplifierCalculated amplifier output
100A1,024W
150A1,536W
200A2,048W
300A3,072W

These figures are calculated using 12.8V at the amp and 80% efficiency. They are not test results or a promise that every battery will hold that voltage while you play.

The result changes with voltage and amp efficiency. Class AB amps need a different efficiency allowance, and poor cables or connections reduce the voltage reaching the amp.

A 3,000W RMS amplifier would require about 293A at 12.8V and 80% efficiency to produce its full rated output. A single 100A storage battery cannot supply that full-output demand continuously on its own.

For the method and further examples, see our guide to calculating amplifier current draw from RMS watts.

Your Alternator Helps, and Music Demand Varies

Your amp is not drawing its maximum current every second of every song. How loud you play, the track, the speaker load and how long the bass holds all make a difference.

With the engine running, the alternator can supply some of the current. A 100A secondary battery therefore does not automatically put a 1,000W limit on the whole system.

The battery still has to handle its share. Sitting at idle with a long bass track playing can ask much more of it than normal driving. Use our battery and alternator sizing calculator to plan the setup, then check what happens while the system is playing.

High-Current LiFePO₄ and SCiB LTO Are Different Options

LiFePO₄ can still be a good choice for serious car audio. A bank built to deliver high current can be very different from a camping battery, even though both use the same chemistry.

Evolution Lithium’s EVE LiFePO₄ car-audio bank range uses 22Ah cells and an integrated active balancer. The published maximum charging voltage is 14.6V. Choose the bank size around your amps, charging setup and how you use the system.

Toshiba SCiB LTO is another platform. Toshiba’s high-power SCiB cell documentation describes cells designed for high-power charging and discharging. The finished bank still needs suitable connections, hardware and current ratings. A short peak figure for one cell does not tell you what the whole bank can deliver continuously.

For our high-output 6S SCiB setups, we generally aim for 15.6–15.9V, with the bank and all vehicle equipment checked for compatibility. Your alternator and amps must suit that voltage. Never apply that charging setting to a conventional 4S LiFePO₄ battery.

Explore the 3Ah SCiB LTO bank range.

Check Charging and Installation Before Connecting Anything

A battery does not become a safe match for your car just because it is going in the boot.

Before connecting it, check:

  1. Charging voltage: Check what your alternator actually does. Some vehicles change charging voltage as you drive. The battery must suit that behaviour.

  2. Charging amps: Check how much charging current the battery can accept. This can differ from what it can deliver to the amp.

  3. How it connects: Have the charge path between the alternator, starting battery and rear bank planned properly. Do not directly parallel an LTO bank with an AGM battery.

  4. Mounting: Secure the lithium bank in the boot or a suitable protected rear/interior location, away from engine-bay heat. Cover exposed terminals.

  5. Cables and fuses: Use cable, connections and fuses sized for the job. A cable fed by a battery at each end needs appropriate fuse protection at both sources.

If the design allows a direct parallel connection, follow the correct charging or pre-charge procedure to bring the bank to a compatible voltage first. Matching the voltage reading does not make different chemistries a suitable pairing.

Our two-battery car-audio wiring guide covers the installation considerations in more detail.

Questions to Ask Before Buying a Secondary Battery

Ask the seller for the exact model, then confirm:

  • Continuous discharge current, including temperature restrictions.
  • Peak current, permitted duration and overload recovery behaviour.
  • Required charging voltage and maximum charging current.
  • Whether the intended vehicle use and connection arrangement are permitted.
  • Terminal requirements and any restrictions on parallel operation.

Tell your installer which amps you run, what load they are wired to, how loud you play and what your alternator supplies. “It’s a 100Ah lithium” leaves out the details that decide whether it will work.

Frequently Asked Questions

Is a 100Ah Lithium Battery Enough for a 2,000W Amp?

Check its amp rating first. At 12.8V and 80% efficiency, 2,000W output needs about 195A. A battery rated for 100A cannot supply that continuously by itself. Your alternator and how you play the system also matter.

Does a 200A BMS Guarantee 2,000W RMS?

No. About 2,000W is an estimate at 12.8V and 80% efficiency. The voltage at your amp, its efficiency, temperature and wiring all affect the result. Give the battery some breathing room rather than expecting it to sit at its maximum rating.

Are All Solar LiFePO₄ Batteries Unsuitable for Car Audio?

No. Some suit smaller daily setups or extra playing time, and some models can deliver much more current. Check the exact battery against your system. The word “solar” on the listing does not settle it either way.

Can I Add Another Storage Battery to Increase Current?

Possibly, if the manufacturer allows it and the installation is designed for it. Batteries do not always share current evenly. If one disconnects, the others suddenly have more work to do, so simply adding the ratings together can be misleading.

Conclusion

A good second battery needs to keep up with your amp, work with your charging system and give you enough playing time. Check all three before spending money.

A 100–200A storage battery may be fine for a smaller daily setup. If you want long demos on a big monoblock, check that current rating closely. Roughly 1,000W RMS per 100A is a useful starting point, with voltage, amp efficiency and alternator support taken into account.

Find a Bank That Suits Your Sounds

Running a conventional 12V setup? Start with our EVE LiFePO₄ car-audio banks and check the charging requirements against your vehicle. Building around compatible higher-voltage charging for demos or SPL? Take a look at our 3Ah SCiB LTO banks.


Not sure which way to go? Send Gary your setup. Include your amp models, what load they are wired to, charging voltage and whether you want daily listening, engine-off playing time or long demos. 

send that through too, so we can check whether it suits the job.